MOTOWELD-X350 INSTRUCTIONS (R1)

September 23, 2026 20:33
Updated

1 Basic Specifications

2 Welding Power Source Installation and Connection

2.1 Installation Site and Welding Power Source Environment

2.2 Precautions on Grounding

2.3 Power Supply Installed Capacity and Connection Cables

2.4 Combination with Earth Leakage Breaker

2.5 Connection of Electrical System

2.6 Connection of Welding Voltage Sensing Cable

2.6.1 Connection in the Welding Power Source Side

2.6.2 Connection to the Work

2.6.3 Connection example of Welding Voltage Sensing Cable

2.7 Connection of Shielding Gas System

2.7.1 For Mixed Gas or Carbon Dioxide Gas Welding

2.7.2 Installation Site and Gas Cylinder Environment

2.8 Ambient Environment

2.9 Precautions on Transporting

3 Welding Preparation

4 Operations on Panel

4.1 Explanation of Welding power source Panel

4.2 Explanation of Welding power source Panel

4.2.1 Parameters confirmation method

4.2.2 Changing Common (C) Parameters

4.2.3 Communication Setting

4.2.4 Saving Welding Conditions

4.2.5 System Reset

5 Setting in the Robot Control Unit Side

5.1 Digital Communication Setup

5.2 Welding Unit Characteristics Setup

5.3 Welding power source Basic Setup

5.3.1 Security Mode Change

5.3.2 Welding power source Setup Screen Display

5.3.3 Feeder Motor Selection

5.4 Welding Method Setup

5.5 Welding Job Making

6 Welding power source Customization

6.1 MOTOWELD Screen

6.1.1 MOTOWELD Screen (Online/Offline)

6.1.2 Parameter Discrepancy Screen

6.1.3 Note and Procedure When Switching the Welding Power Source

6.2 Welder prm. Screen

6.2.1 Gas/Wire Screen

6.2.2 Other Screen

6.2.3 All PRM. screen

6.3 Customize Screen

6.3.5 Aluminum MIG Pulse Welding Characteristics

6.3.6 Welding Current Output Characteristics

6.3.7 Heat And Wave Form Control (HAWC) Screen

6.3.8 All PRM. Screen

6.4 Maintenance Screen

6.5 External Memory

6.5.1 Setting Contents Save

6.5.2 Setting Contents Reading

7 Welding Operation

7.1 Checking the Welding Conditions

7.2 Wire Stickout

7.3 Direction of Welding and Torch Angle

8 Precautions on Welding

8.1 Error Detection Function

8.2 Tripped Breaker of the welding power source

8.3 Precautions on Welding Operations

9 Location and Setting of Printed Boards

9.1 Location of Printed Boards

9.2 Internal Selecting Switches

9.2.1 DIP Switch Settings for Pr(MB)-031Board

9.2.2 DIP Switch Settings for Pr(CR)-031 Board

10 Maintenance and Inspection

10.1 Cleaning of Dust Protective Filter

10.2 Replace Fuse

11 Failure Analyses

11.1 Confirming Setting conditions

11.2 Cause and Remedy of Welding Section Failure

11.3 Cause and Remedy of Failure at Electrical Circuit Section

12 Robot Interface Signals

12.1 Specifications of Robot Digital Interface Signals

12.2 Description and Function of Signal Output Terminals for Monitor

12.3 Meaning and Function of Signal for Starting Point Detection Function (Optional board Pr (OP2)-001)

13 Connection System Diagram

14 Welding power source Condition File of the Robot Controller

15 List of Service Parts

16 List of Parameters

6.1 List of Process Parameters

6.2 List of Common Parameters

16.3 List of D Parameters

17 List of Welding Types

18 List of Errors

Comments

0 comments

Article is closed for comments.