Fieldbus PCI-Card Instruction Manual (R2)

August 31, 2026 20:19
Updated

1.1 About this manual

1.1.1 Copyright

1.2 System requirements

1.2.1 NX100 Software

1.2.2 DX100/DX200 software

1.3 In manual included Fieldbus PCI-cards and NetTools

1.5 Handling ESD sensitive devices

1.6 Manufacturer

1.7 Introduction

1.9 Fieldbus systems

1.10 Introduction to the fieldbus PCI-cards

1.11 Hardware compatibility

2.1.1 Specification

2.1.2 Technical specification

2.1.3 Compliances and conformances

2.2 Hardware installation

2.2.1 NX100 Installation

2.2.2 DX100/DX200 Installation

2.2.3 Mount Board YRC1000

3 Software configuration

3.1.1 Enable the PCI card

3.2 DX100 Manual I/O allocation (FD 134)

3.3.1 Fieldbus input data map

3.3.2 Fieldbus output data map

3.4 Fieldbus status byte

4 General installation in IP-based networks

4.1.1 No answer from ping

4.1.2 Only one Ethernet cable used

4.1.3 Logical Networks

4.2 Anybus IPconfig

4.2.1 The module is not shown

4.2.2 The module has IP address 0.0.0.0

5 Profibus DPV1 Slave AB3601

5.1 Profibus Interface Details

5.2.1 Status LEDs

5.2.2 Connectors 9-pin D-sub

5.3 PROFIBUS network setup

6 Profibus DPV1 Master AB3602

6.1 Profibus interface details

6.2.1 Status LEDs

6.3 PROFIBUS network setup

6.3.1 AnyBus NetTool for PROFIBUS

6.3.2 Termination

6.3.3 Node settings

6.3.4 Configuration online

7 DeviceNet Adapter Slave AB3603

7.1 DeviceNet Interface Details

7.2.1 Status LEDs

7.2.2 Connectors

7.3 DeviceNet network setup

8 DeviceNet Scanner Master AB3604

8.1 DeviceNet Interface Details

8.2.1 Status LEDs

8.2.2 Connectors

8.3 DeviceNet network setup

8.3.1 AnyBus NetTool for DeviceNet

8.3.2 Termination

8.3.4 Configuration online

8.3.5 Configuration with RSNetworx from Rockwell

9 AS-Interface Master AB3605

9.1 AS-Interface Master

9.2.1 Status LEDs

9.2.2 Connectors

9.2.3 Rectifying of interruption

9.3 Principle of Input/Outputs in ASI

9.4 Configuration interface

9.4.1 Menu Tree overview

9.4.2 Change settings

10 EtherNet/IP Adapter/Modbus TCP Slave AB3606

10.1 EtherNet/IP Adapter/Modbus TCP slave interface details

10.2.1 Status LEDs

10.3 Network setup

10.3.1 EIP setup

10.3.2 Modbus/TCP

11 EtherNet/IP Scanner Master AB3607

11.1 EtherNet/IP Scanner master interface details

11.2.1 Status LEDs

11.3 Network setup

11.3.1 EDS file

11.3.2 Configure via AB3607's on-board web server

12 PROFINET-IO Slave AB3609

12.1 PROFINET-IO Slave Interface Details

12.2.1 Status LEDs

12.3 Network setup

13 FL-Net AB3610

13.1 FL-Net Interface Details

13.2.1 Status LEDs

13.3 Network setup

14 FIPIO Slave AB3611

14.1 FIPIO Interface Details

14.2.1 Status LEDs

14.3.1 Setup in Schneider’s “UNITY” programming environment

15 Interbus-S Slave AB3615

15.1 Interbus-S Interface Details

15.2.1 Status LEDs

16 CanOpen Slave AB3616

16.1 CanOpen Interface Details

16.2.1 Status LEDs

16.3.1 Network configuration

17 EtherCAT slave AB3617

17.1.1 Interface details

17.2.1 Status LEDs

17.2.2 State Description

17.3 Network Setup

17.3.1 Omron tools

18 PL-IB 300 Powerlink

18.1 Powerlink Controlled Node details

18.3 Network setup

18.3.1 Installing the XDD file in B&R Automation Studio

18.3.2 Configure IO in B&R Automation Studio

Comments

0 comments

Article is closed for comments.